NFC Epoxy Sticker
The NFC Epoxy Sticker is a more durable alternative to regular NFC labels that peel, fade, or break when they are exposed to water and mechanical stress. An NXP NTAG-series chip and an ISO/IEC 14443A antenna are protected inside UV-resistant epoxy resin in each tag. This gives each tag an IP67 rating and a temperature range of -25°C to +70°C for use. The 1–2mm shape gives a smooth 3D look to the product without changing its look, which makes it a good choice for both managing industrial assets and branding products that people see.
A paper or PVC NFC label works well in controlled environments, but it tends to peel, change colour, and break down when it comes in contact with grease, water, or repeated physical contact.
This problem can be fixed with an NFC Epoxy Sticker, which has a secure plastic shell around the chip and antenna. The sealed tag can withstand scratches, moisture, and common chemical exposure, such as alcohols and oils, but it still works fully as an NFC reader.
This format is good for uses that need both toughness and a smooth, shiny surface because the clear finish gives the impression of three-dimensional depth.
| Parameter | Specification |
|---|---|
| Operating Frequency | 13.56 MHz (HF) |
| Communication Protocol | ISO/IEC 14443A, NFC Forum Type 2 / Type 4 |
| Chip Model | NXP NTAG213 / NTAG215 / NTAG216 |
| Reading Distance | 0 – 10 cm |
| Storage Capacity | 144 bytes / 504 bytes / 888 bytes |
| Material | Industrial-grade epoxy resin (transparent or white) |
| Protection Rating | IP67 (dust-tight and immersion-resistant) |
| Operating Temperature | -25°C to +70°C |
| Thickness | 1 – 2 mm |
| Installation Method | 3M adhesive / direct bonding |
| Data Retention | 10 years |
| Write Cycles | 100,000 cycles |
| Size | Multiple standard sizes; custom sizes supported |
Epoxy Encapsulation
The plastic shell has a Shore D hardness of 70 to 80, which means it can withstand physical damage, water, and typical industry chemicals like oils and alcohols.
Resin that doesn't fade in UV light
The epoxy uses a UV-stable AB glue recipe that is made to keep the clearness of the vision outside. To test for yellowing resistance, accelerated ageing tests act like being in the sun for 24 months.
Form Factor with Low Profile
The tag is only 1–2 mm thick, so it fits flush against most surfaces. The clear finish gives the look of depth without making the package bigger or covering up the images that are already there.
Wide Range of Smartphone Compatibility
The tags work at 13.56 MHz and are compliant with NFC Forum Type 2/4. Smartphones that are NFC-enabled can read them without needing a special app for basic tap-to-read functions.
There is an on-metal version.
You can use a ferrite shielding layer on metal surfaces to get reliable read performance on things like machinery, metal containers, and conductive housings.
Options for customisation
It can print in CMYK colour, silk-screen artwork, laser engrave, encode serial numbers, and cut forms. The artwork is made under the epoxy layer, which keeps it from getting scratched on the surface.

Following the guidelines set by ISO 9001:2015, each NFC Epoxy Sticker goes through a number of steps of review.
Frequency Resonance Testing—Equipment for resonance analysis is used to make sure that chip performance is the same across production batches.
Accelerated Ageing and UV Exposure Testing—Verifies the clarity and structural stability of the epoxy over a hypothetical 24-month time of exposure to the sun.
glue Peel Strength Testing (ASTM D3330): This test confirms that 3M glue can stick to glass, plastic, and covered surfaces.
Salt Spray Testing—Checks the antenna-chip interface when it is exposed to high humidity and salt.
When you do vacuum leak testing, you can be sure that the epoxy coating is strong and that the IP67 grade is always met.
A reported defect rate of less than 0.3% across all production runs is possible with this process.

Product Anti-Counterfeiting
When used on makeup, drinks and electronics packages, the epoxy shell is hard to change. Customers can use their phones to scan the tag to make sure it's real, and the coating can't be taken off without damage being noticeable.
Taking care of industrial assets
Technicians can tap the tag to get to maintenance records or equipment data even when it's exposed to grease, dust, or water in manufacturing and logistics settings. The tag won't break down over time.
Packaging for Food and Medicine
These tags can be used in cold chains and clean rooms where regular adhesive labels often fail because they have an IP67 rating and can withstand chemicals.
Accessories for pets and clothes
When the tag is attached to a collar or other wearable item, it can handle rain, mud, and physical damage while still holding contact or identification information.
Engaging with Luxury Brands
The tag is built into high-end product packaging and lets customers get to brand content, insurance registration, or advertising experiences with just one tap.

The product can be made by both OEM and ODM at WS RFID. The following options are available:
For lead times on certain configurations, you should talk to the sales team directly.

Q: Can the product be used on metal?
A: Standard versions aren't made to work best with metal. WS RFID has a version that works well on metal that has a ferrite protecting layer to make sure it works well on machinery, metal casings, and electric containers.
Q: Will the epoxy glue get yellow over time?
A: The UV-stable AB glue is made so that it won't turn yellow. Accelerated ageing tests check how well transparency stays the same after being exposed to the elements for 24 months.
Q: Is printed art safe from getting scratched?
A: Under the epoxy layer, custom CMYK or silk-screen artwork is printed. This layer protects the artwork from surface wear over the tag's useful life.
Q: What are the ratings for the chip's ability to hold data and write to it?
A: The NXP NTAG series chips can store data for 10 years and be written to 100,000 times.
Q: Can I use my own shapes?
A: Yes. The epoxy moulding process can make custom die-cut shapes besides circles and squares. These can be brand logo outlines and profiles made just for one use.
Q: How long is the wait time, and how much does the MOQ need to be?
A: Products that are in stock usually ship within 5 to 7 business days. Orders that aren't in stock or are made to order usually take 10–12 business days. The smallest amount that can be ordered is 500 units.
Do you have more questions about NFC Epoxy Sticker? Send your specifications or sourcing questions to kenny@w-srfid.com.